The Week in Review β 2026-20
βοΈ It probably interests nobody, but since I was so happy about it, I want to mention it: Honeycomb Bravo Profiles for X-Plane is the configurator that integrates the Honeycomb Bravo into X-Plane extremely well with minimal effort, including various ready-made profiles for different aircraft.
The autopilot row (buttons and rotary switches) and the trim wheel were previously only partially functional; now they work as you would expect. All 14 annunciator LEDs are working now as well.
π‘ Three weeks ago I wanted to cut the lawn in the garden a bit shorter, but then a series of rainy days began. At other times I had other things to do, so I didn’t get around to it and the lawn has now gone five or six weeks without being mowed.
You can imagine what it looks like now after two weeks of alternating rain and sunshine, because that combination is ideal for growth. All we’re missing is a few warm days and we’ll have our own jungle in front of the house. Time for me to take care of it.
πΊοΈ Every week I tell myself, “take it a bit easier with Bikerouter now,” and then I either get an idea or browse through the long to-do list. In any case, I always end up finding something to do again.
Last week I fixed some smaller bugs and inconsistencies (but there are still countless of them!).
I also worked on new features:
-
The route line gets direction arrows
-
A new route inspector (“Route Inspector”) makes it possible to inspect path segments and points directly on the route. It can display the details of a selected path/point, e.g. surface, way type, etc. Basically, this is the inverse of the detail table in the right sidebar.
The route inspector is activated via the “Info” button and can also be deactivated there again. This also works with the keyboard and the shortcut i).
Display of all tags present in the routing data for a path segment. The new tags from BRouter 1.7.9 are already included here as well π
All of the changes listed are not online yet; I hope, though, that I can finish the release this week.
Other than that, I continue to work on the migration to the new BRouter version and the first Bikerouter test instance with the new engine is already online. I don’t think the migration will take much longer now.
π¨ During the week I did a bit of DIY work again, although only in a supporting role during a remodeling job.
A bathroom being renovated had already been fully tiled, but all the other work was done by ourselves:
- Redo the suspended ceiling and install and connect ceiling lights
- Install the toilet
- Install the shower fixture
- Mount the radiator
- Hang the cabinets
- Mount the sink
It was fun, even if it was a bit exhausting at times. And here and there I learned a little something (e.g. soldering copper fittings) β and learning is always the most important thing.
π§ New additions in the workshop: a new Diagonal Cutter, Wire Stripping Tool and another Super Knips.
My old cheap hardware-store diagonal cutter has had a nasty nick in the cutting edge for many years, coincidentally exactly in the upper half, i.e. at the place where in most cases I position the wire/cable.
So I always needed at least two attempts to cut through it. Every single time it annoyed me, but on the other hand I used it too rarely and therefore never bothered replacing it.
The nick always reminds me how much energy there is in a little bit of household electricity: it was caused by a short circuit between phase and neutral in a 230-volt circuit. The few milliseconds before the circuit breaker did its job were enough to tear a good chunk out of the hardened cutting edge.
π CLI tool of the week:
Graphics in SVG format that I use on the web, I always drag and drop once onto SVGOMG beforehand. In almost all cases, this saves a few bytes to a few kilobytes.
With svgo, this feature also exists as a command-line tool, and that now makes my work much easier and saves me a context switch.
I don’t know why I didn’t discover this earlier, especially since it is linked right at the top of the SVGOMG website π€·ββοΈ
π Listened to this week:
Questions or comments?
The easiest way to reach me is on Mastodon.